On larger tractors, it is pretty much standard equipment anyway, so the choice is made for you.Toe in toe out in tractor. Do you need draft control? On the smaller tractors, probably not, as these tractors are rarely used to do much plowing. To get the maximum benefit from draft control, you must use it the way the manufacturer intended for it to be used. The whole job was a giant pain in the, especially the position control eccentric, because there is a snap ring. We have to give the system a little time to settle down somewhere in the raise/lower cycle, and that is the function of the response control. I disassembled the draft control to replace the seals, including the position control eccentric (the shaft toward the right rear of the housing that has an o-ring on the inside and a snap ring on the outside). However, if we let the plow go back into the ground at an uncontrolled speed, we will end up pulling a plow that jumps into and out of the ground. Response control has no effect on rate of lift, and that is good, because we want the plow to raise quickly when we hit a hard spot. By slowing this rate, we minimize undesirable oscillations that would otherwise occur. Response control (in most systems we know of) simply serves to control the rate at which hydraulic oil is allowed to escape from the lift cylinder. This is accomplished with something called…. Now, with all of this draft action going on, we've got to slow the lift system down some, or we'll end up with a rapid, out of control oscillation of the lift arms going up and down. Still others use a torsion bar that is actually twisted as the top link moves toward and away from the tractor. Other tractors (namely European style) have a massive leaf type spring between the top link and the lift cover. This compression/relaxation causes movement in the draft control linkage, thus changing the position on the control valve, raising and lowering the lift arms as needed. For a large portion of North American style tractors, there is a rather large (usually internal) coil spring, which is compressed (by the top link) as draft load increases, and relaxed as the load diminishes. For tractors that utilize top link draft sensing, there are several methods in use to transmit draft load information to the control valve. Movement of these electronic bars is almost undetectable to the eye. With these, the lower draft bar contains a strain sensor which sends a signal to an onboard computer. There are also tractors on the market that incorporate an electronic lift control system. In the case of lower link sensing, the front of the lift arms are attached to a common bar that flexes with variable loading to impart movement to linkage that is ultimately connected to the control valve. Generally you will find lower link sensing on larger, higher horsepower tractors. Both achieve the same end result, and much discussion could be made over which is the best method. They are: lower link draft sensing, and top link draft sensing. There are two main types of draft sensing in wide use today. After you get past the hard spot in the field, the draft control automatically returns the plow to the pre-selected, ideal depth. 2N and 8N tractors have Draft Control Avoiding driving on steep hillsides He. If the strain exceeds a predetermined level, the draft control will automatically raise the plow just enough to restore normal loading of the tractor. 4 wheelbase Size Push or pull the tractor to the desired spot I checked. Draft control senses the amount of strain that the tractor is being subjected to from the plow. We also do not want to have to continually fiddle with the lift controls, raising and lowering the plow by small amounts, as ground conditions vary throughout the field. We want to be able to plow at a reasonable depth without straining the engine or having excessive tire slippage. It is very unlikely that the latter will happen. The natural tendency is for the plow to continue down until the tractor either loses traction, runs out of power, or the lift arms reach their lower limit. As the plow continues down, traction and horsepower requirements increase. As you let the lift arms down, and begin to move forward though the field, the plow will start to enter the ground. A note about plowing- if you have adjusted the plow properly, you should not have to use the stabilizer system to keep it running true behind the tractor. We've mounted our plow to the three point hitch and adjusted things so that the plow will run straight and track properly behind the tractor. For illustration purposes, let's assume we want to go plow up the back forty.
Draft control, while not essential, makes life a little easier when plowing, sub-soiling, or using other ground engaging implements.
0 kommentar(er)
